Still have questions? Visit our Community Forum.INet - one of the the best network scanner for iOS since 2009. How to set the load balance when multiple Internet access methods are used at the same time?.How to set the priority of each Internet access method?.The router's 5G WiFi will switch to the non-DFS channel if the upstream WiFi is not scannable or if the connection fails. If the upstream WiFi uses a DFS channel and is scannable, the router's 5G WiFi will use the same channel. When Repeater to a upstream 5G WiFi, the router WiFi will fellow the upstream WiFi to use or not use the DFS channel. Solution: Please check if the upstream device of Repeater has internet access. Warning: The interface is connected, but the Internet can't be accessed with IPv4 protocol. To determine whether you can access the Internet or not, please go to Multi-WAN page. When Internet access is not available, the corresponding warning is displayed. In the connecting phase, the Main Wi-Fi on the corresponding band may be disconnected for a few seconds. For GL-AXT1800 and GL-AX1800, the Guest Wi-Fi will be temporarily turned off. In the scanning phase, data packet may loss in the scanned band, possible connection problems for new devices. Note: There are some problems during the scanning phase and the connection phase. It can be divided into three phases, the waiting phase, the scanning phase, and the connecting phase. The wrong SSID/password was entered during the process of Repeater, after the first failed connection.Īfter connecting to the WiFi of the upstream router, the router moves out of the signal range of the upstream router.Īfter connecting to the WiFi of the upstream router, the upstream router changed the SSID/password, or restricted the connection. You can turn off the reconnection manually, and for ssid/password errors, please delete it in Known Network. In the following cases, the router's Repeater will try to connect to WiFi every once in a while. WPA/WPA2/WPA3 Enterprise, for Extensible Authentication Protocol (EAP), it requires a username and password for authentication. Input the SSID, for Security, It has the following three options. If the SSID is not in the Available Networks list, or if the SSID is hidden, you can click Join Other Network. On the Known Network sector, click trash icon to delete a known network, click cog icon to config the network. To delete known network, click Switch Network. If the option is enabled, The device will prompting the stability of the connection in exchange of reducing the connection speed. If the option is enabled, 5GHz Wi-Fi will be temporarily unavailable when a radar is using the channel which is currently router using Otherwise, the router will not connect to any Wi-Fi using DFS channels.įorce 20MHz Bandwith For 2.4G. If you manually select a band, the router will not scan or connect to any Wi-Fi with another band.Īllow Repeat DFS Channels. If the option is enabled, the router will automatically connect to other saved networks when it is unable to connect to the current Wi-Fi network.īand Selection. If this option is enabled, the router will only connect to the AP corresponding to the BSSID you selected when switching to a network using this SSID.Īllow Switching To Other Saved Network. When joining the network, there are two additional options. Wait a moment, if the password is correct, the connection will be successful. If the SSID you want to connect to is not in the list, click Join Other Network in the image above. Basic steps ¶Ĭhoose a SSID from the drop-down list and enter its password. On the left side of web Admin Panel -> INTERNET, Repeater sector. It works in WISP (Wireless Internet Service Provider) mode by default, which means that the router will create its own subnet and act as a firewall to protect you from the public network. when you are using free Wi-Fi in a hotel or cafe. Using Repeater means connecting the router to another existing wireless network, e.g. Connect to a Hotspot with a Captive PortalĪccessing client LAN from Server(WireGuard)Ĭonnect to the Internet via an existing Wi-Fi by Repeater ¶
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |